 |
Settings |
MCACC
Operation:
Use the on-screen displays (OSD) that appear on the TV to make the settings.
Press 
on the remote controller to display the Home screen, then select MCACC with the cursors on the remote controller and press ENTER.
Select the item with the cursor 
/
/
/
buttons of the remote controller and press ENTER to confirm your selection.
Use the cursors 
/
to change the default values.
To return to the previous screen, press 
.
To exit the settings, press 
.
Full Auto MCACC
Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also automatically adjusts the equalizers for the speakers and enables correction of distortion caused by the acoustic environment of the room.
Calibration takes several minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. Keep the room as quiet as possible during measurement. If the measurement is interrupted, turn off the household appliances.
1.Place the supplied speaker setup microphone in the listening position, and connect to the MCACC SETUP MIC jack on the main unit.
When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place.
To cancel Full Auto MCACC partway through, disconnect the speaker setup microphone. You cannot use any other menu options while it is connected.
2.Select the connected speaker configuration.
The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings.
Use this screen to select whether you have connected a subwoofer and to select the type of height speaker, etc.
If you have connected a subwoofer, check the power and volume of the subwoofer. The low frequencies played by the subwoofer may not be discernible, so set its volume to at least halfway.
3.Test tones are emitted by the speakers, and firstly the unit detects the speakers connected and the noise in the environment.
4.After the results of the above measurements are displayed, select "Next", press ENTER on the remote controller, and the test tones are emitted again, and the unit automatically makes settings such as the optimum volume level and the crossover frequency.
5.When the measurement is completed, the measurement result is displayed.
Press the cursors 
/
on the remote controller to check the settings. Press ENTER when "Save" is selected to save the settings.
6.Disconnect the speaker setup microphone.
Manual MCACC
EQ Adjust
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
/
, adjust the volume of that frequency between "－12.0 dB" and "＋12.0 dB" with 
/
.
on the remote controller, and select the Preset you want to adjust in "AV Adjust" - "MCACC" - "Manual EQ Select" first.MCACC Data Check
You can check the number of speaker channels connected and the content and values you have set for each of the speaker settings.
Speaker Setting
Channel Level
Speaker Distance
Acoustic Calibration EQ
