|
Advanced Setup |
MCACC
Operation:
Use the on-screen displays (OSD) that appear on the TV to make the settings.
Press on the remote controller to display the Home screen, then select MCACC with the cursors on the remote controller and press ENTER.
Select the item with the cursor /// buttons of the remote controller and press ENTER to confirm your selection.
Use the cursors / to change the default values.
To return to the previous screen, press .
To exit the settings, press .
Full Auto MCACC
Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also automatically adjusts the equalizers for the speakers and enables correction of distortion caused by the acoustic environment of the room.
Calibration takes between 3 and 12 minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. Keep the room as quiet as possible during measurement.
If you have connected a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than halfway.
If the power of this unit suddenly turns off, the wires in the speaker cables may have touch the rear panel or other wires and tripped the protection circuit. Twist the wires again properly and make sure they do not stick out of the speaker terminals when connecting.
1.Place the supplied speaker setup microphone in the listening position, and connect to the MCACC SETUP MIC jack on the main unit.
When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place.
2.Select the connected speaker configuration.
The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings.
3.Test tones are emitted by the speakers, and firstly the unit detects the speakers connected and the noise in the environment.
4.After the results of the measurements are displayed, select "Next", press ENTER on the remote controller, and the test tones are emitted again, and the unit automatically makes settings such as the optimum volume level and the crossover frequency.
5.When the measurement is completed, the measurement result is displayed.
Press the cursors / on the remote controller to check the settings. Press ENTER when "Save" is selected to save the settings.
6.Disconnect the speaker setup microphone.
Manual MCACC
EQ Adjust
If you perform Full Auto MCACC then settings are automatic, but you can also adjust the output volume of the range of each connected speaker to suit your own preferences. You can adjust the volume of the different sound ranges for each of the speakers. You can set three different equalizers in Preset 1 to 3. You can select up to 4 bands for the Subwoofer and 9 bands for all other speakers.
Front Left
Default Value: 0 dB
Center
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Front Right
Default Value: 0 dB
Height Left
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Height Right
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Surround Right
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Surr Back Right
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Surr Back Left
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Surround Left
Default Value: 0 dB
After selecting the speaker frequency from between "63 Hz" and "16 kHz" with the cursors /, adjust the volume of that frequency between "-12.0 dB" and "+12.0 dB" with /.
"63 Hz" can only be selected when this speaker is set to "Large" in "System Setup" - "Speaker" - "Crossover".
If an item cannot be selected even though connection is correct, check that the settings in "System Setup" - "Speaker" - "Configuration" - "Speaker Channels" matches the number of connected channels.
Subwoofer
Default Value: 0 dB
The result may not be as expected depending on the input source and listening mode setting.
If you want to make the adjustments while listening to something, press on the remote controller, and select the Preset you want to adjust in "AV Adjust" - "MCACC" - "Manual EQ Select" first.
MCACC Data Check
You can check the number of speaker channels connected and the content and values you have set for each of the speaker settings.
Speaker Setting
You can check the number of speaker channels connected and the large and small settings you have set for the low range reproduction capabilities for each of the speakers.
Channel Level
You can check the output level settings for each of the speakers.
Speaker Distance
You can check the distance from each speaker to the listening position.
Acoustic Calibration EQ
You can check the calibration values for the frequency characteristics of each speaker that were set in "Manual MCACC".
SN 29402995AHTML
(C) Copyright 2017 Onkyo & Pioneer Corporation Japan. All rights reserved.