 |
Settings |
Firmware Update
Updating via USB
Preparation:
Prepare a 128MB or larger USB storage device. FAT16 or FAT32 file system format.
–Media inserted in a USB card reader may not be used for this function.
–USB storage devices with security function are not supported.
–USB hubs and USB devices with hub function are not supported. Do not connect these devices to the unit.
Delete any data stored on the USB storage device.
Turn off the controller component (PC etc.) connected to the network.
Stop any playing Internet radio, USB storage device, or server content.
If "HDMI CEC" is set to "On", set it to "Off".
–Press 
on the remote controller to display the Home screen. Next, select "System Setup" - "Hardware" - "HDMI", press ENTER, select "HDMI CEC" and select "Off".
＊Some USB storage devices may take long to load, may not be loaded correctly, or may not be correctly fed depending on the device or their content.
＊Our company will not be liable whatsoever for any loss or damage of data, or storage failure arising from the use of the USB storage device with this unit. Thank you for your understanding.
＊The description may differ from the on-screen display but that will not change the way to operate or the function.
Update
1.Connect the USB storage device to your PC.
2.Download the firmware file from our company's website to your PC and unzip.
Firmware files are named in the following way:
PIOAVR＊＊＊＊_＊＊＊＊＊＊＊＊＊＊＊＊.zip
Unzip the file on your PC. The number of unzipped files and folders varies depending on the model.
3.Copy all unzipped files and folders to the root folder of the USB storage device.
Make sure to copy the unzipped files.
4.Connect the USB storage device to the USB port of the unit.
If you connect a USB hard disk drive to the USB port of the unit, we recommend that you use its AC adapter to power it.
If the USB storage device has been partitioned, each section will be treated as an independent device.
5.Press 
on the remote controller.
The Home screen is displayed on the TV screen.
6.Select "System Setup" - "Miscellaneous" - "Firmware Update" - "Update via USB" with the cursors in order, then press ENTER.
If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up.
You will not be able to select "Update via USB" if there is nothing to update.
7.Press ENTER with "Update" selected to start update.
During the update, the TV screen may go black depending on the updated program. In that case, check the progress on the display of the unit. The TV screen will remain black until the update is complete and the power is turned on again.
During the update, do not turn off, or disconnect then reconnect the USB storage device.
"Completed!" is displayed when the update is complete.
8.Disconnect the USB storage device from the unit.
9.Press 
STANDBY/ON on the main unit to switch the unit to standby. The process is completed and your firmware is updated to the latest version.
Do not use 
on the remote controller.
If an Error Message is Displayed
When an error occurs, "＊-＊＊ Error!" is displayed on the display of the unit. ("＊" represents an alphanumeric character.) Check the following:
Error Code
＊-01, ＊-10：
USB storage device not found. Check whether the USB storage device or USB cable is correctly inserted to the USB port of the unit.
Connect the USB storage device to an external power source if it has its own power supply.
＊-05, ＊-13, ＊-20, ＊-21：
The firmware file is not present in the root folder of the USB storage device, or the firmware file is for another model. Retry from the download of the firmware file.
Others
Disconnect then reconnect the AC power cord, then repeat from the beginning.
SN 29402317A HTML
(C) Copyright 2016 Onkyo & Pioneer Corporation Japan. All rights reserved.
Onkyo group has established its Privacy Policy, available at [http://www.pioneer-audiovisual.com/privacy/].
